Добрый день. Подскажите, пожалуйста, в чем может быть проблема? Прерывается звонок ровно через 600 секунд после поднятия трубки, то есть максимальное время разговора не больше 600 секунд. Перерыл все конфиги, но ничего похожего не нашел.
Астериск 1.6.2.13
При чем под конец такого общения идут короткие гудки (3 по 3) и в конце сразу hangup.
Конфигурация входящих звонков такая <Город(аналог)>----<PanasonicTDA-200>----<Астериск>----<та же PanasonicTDA-200>----<аналоговый телефон сотрудника>
CALLWAINTING = no
В чем может быть проблема?

Порнослоники до * по сипу ходят? Или поток?

Извиняюсь, совсем забыл написать про поток. Да, через Е1.

Ну вот поток и дебаж. Какой cause code?

Да, важно понять от кого приходит CALL DISCONNECT по q.931. С чьей стороны.

Enabled debugging on span 1

< Protocol Discriminator: Q.931 (8) len=21
< TEI=0 Call Ref: len= 2 (reference 85/0x55) (Sent from originator)
< Message Type: SETUP (5)
< [04 03 90 90 a3]
< Bearer Capability (len= 5) [ Ext: 1 Q.931 Std: 0 Info transfer capability: 3.1kHz audio (16)
< Ext: 1 Trans mode/rate: 64kbps, circuit-mode (16)
< User information layer 1: A-Law (35)
< [18 03 a1 83 9f]
< Channel ID (len= 5) [ Ext: 1 IntID: Implicit Other(PRI) Spare: 0 Preferred Dchan: 0
< ChanSel: As indicated in following octets
< Ext: 1 Coding: 0 Number Specified Channel Type: 3
Ext: 1 Channel: 31 Type: CPE]
< [70 04 89 31 39 31]
< Called Number (len= 6) [ Ext: 1 TON: Unknown Number Type (0) NPI: Private Numbering Plan (9) '191' ]
-- Making new call for cref 85
Received message for call 0xb6fd9b90 on 0xb7565fd0 TEI/SAPI 0/0, call->pri is 0xb7565fd0 TEI/SAPI 0/0
-- Processing Q.931 Call Setup
-- Processing IE 4 (cs0, Bearer Capability)
-- Processing IE 24 (cs0, Channel Identification)
-- Processing IE 112 (cs0, Called Party Number)
q931.c:6871 post_handle_q931_message: Call 85 enters state 6 (Call Present). Hold state: Idle
q931.c:4524 q931_call_proceeding: Call 85 enters state 9 (Incoming Call Proceeding). Hold state: Idle

> DL-DATA request
> Protocol Discriminator: Q.931 (8) len=10
> TEI=0 Call Ref: len= 2 (reference 85/0x55) (Sent to originator)
> Message Type: CALL PROCEEDING (2)
TEI=0 Transmitting N(S)=100, window is open V(A)=100 K=7

> Protocol Discriminator: Q.931 (8) len=10
> TEI=0 Call Ref: len= 2 (reference 85/0x55) (Sent to originator)
> Message Type: CALL PROCEEDING (2)
> [18 03 a9 83 9f]
> Channel ID (len= 5) [ Ext: 1 IntID: Implicit Other(PRI) Spare: 0 Exclusive Dchan: 0
> ChanSel: As indicated in following octets
> Ext: 1 Coding: 0 Number Specified Channel Type: 3
> Ext: 1 Channel: 31 Type: CPE]
-- Accepting call from '' to '191' on channel 0/31, span 1
-- Executing [191@from_int:1] Dial("DAHDI/31-1", "DAHDI/g1/1039,60,S(700),tT") in new stack
-- Setting call duration limit to 700.000 seconds.
-- Making new call for cref 32794
-- Requested transfer capability: 0x10 - 3K1AUDIO

> DL-DATA request
> Protocol Discriminator: Q.931 (8) len=27
> TEI=0 Call Ref: len= 2 (reference 26/0x1A) (Sent from originator)
> Message Type: SETUP (5)
TEI=0 Transmitting N(S)=101, window is open V(A)=100 K=7

> Protocol Discriminator: Q.931 (8) len=27
> TEI=0 Call Ref: len= 2 (reference 26/0x1A) (Sent from originator)
> Message Type: SETUP (5)
> [04 03 90 90 a3]
> Bearer Capability (len= 5) [ Ext: 1 Q.931 Std: 0 Info transfer capability: 3.1kHz audio (16)
> Ext: 1 Trans mode/rate: 64kbps, circuit-mode (16)
> User information layer 1: A-Law (35)
> [18 03 a1 83 81]
> Channel ID (len= 5) [ Ext: 1 IntID: Implicit Other(PRI) Spare: 0 Preferred Dchan: 0
> ChanSel: As indicated in following octets
> Ext: 1 Coding: 0 Number Specified Channel Type: 3
> Ext: 1 Channel: 1 Type: CPE]
> [6c 02 21 c0]
> Calling Number (len= 4) [ Ext: 0 TON: National Number (2) NPI: ISDN/Telephony Numbering Plan (E.164/E.163) (1)
> Presentation: Unknown (64) '' ]
> [70 05 80 31 30 33 39]
> Called Number (len= 7) [ Ext: 1 TON: Unknown Number Type (0) NPI: Unknown Number Plan (0) '1039' ]
> [a1]
> Sending Complete (len= 1)
q931.c:4959 q931_setup: Call 32794 enters state 1 (Call Initiated). Hold state: Idle
-- Called g1/1039

< Protocol Discriminator: Q.931 (8) len=10
< TEI=0 Call Ref: len= 2 (reference 26/0x1A) (Sent to originator)
< Message Type: CALL PROCEEDING (2)
< [18 03 a9 83 81]
< Channel ID (len= 5) [ Ext: 1 IntID: Implicit Other(PRI) Spare: 0 Exclusive Dchan: 0
< ChanSel: As indicated in following octets
< Ext: 1 Coding: 0 Number Specified Channel Type: 3
< Ext: 1 Channel: 1 Type: CPE]
Received message for call 0x840c020 on 0xb7565fd0 TEI/SAPI 0/0, call->pri is 0xb7565fd0 TEI/SAPI 0/0
-- Processing IE 24 (cs0, Channel Identification)
q931.c:6998 post_handle_q931_message: Call 32794 enters state 3 (Outgoing Call Proceeding). Hold state: Idle
-- DAHDI/1-1 is proceeding passing it to DAHDI/31-1

< Protocol Discriminator: Q.931 (8) len=48
< TEI=0 Call Ref: len= 2 (reference 26/0x1A) (Sent to originator)
< Message Type: ALERTING (1)
< [1e 02 81 88]
< Progress Indicator (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) 0: 0 Location: Private network serving the local user (1)
< Ext: 1 Progress Description: Inband information or appropriate pattern now available. (8) ]
< [1c 25 91 aa 06 80 01 00 82 01 00 8b 01 00 a1 17 02 01 41 06 04 2b 0c 09 01 80 0c cc f3 f1 e8 ed 20 d0 f3 f1 eb e0 ed]
< Facility (len=39, codeset=0) [ 0x91, 0xAA, 0x06, 0x80, 0x01, 0x00, 0x82, 0x01, 0x00, 0x8B, 0x01, 0x00, 0xA1, 0x17, 0x02, 0x01, 'A', 0x06, 0x04, '+', 0x0C, 0x09, 0x01, 0x80, 0x0C, 0xCC, 0xF3, 0xF1, 0xE8, 0xED, ' ', 0xD0, 0xF3, 0xF1, 0xEB, 0xE0, 0xED ]
Received message for call 0x840c020 on 0xb7565fd0 TEI/SAPI 0/0, call->pri is 0xb7565fd0 TEI/SAPI 0/0
-- Processing IE 30 (cs0, Progress Indicator)
-- Processing IE 28 (cs0, Facility)
-- Delayed processing IE 28 (cs0, Facility)
ASN.1 dump
Context Specific/C [10 0x0A] <AA> Len:6 <06>
Context Specific [0 0x00] <80> Len:1 <01>
<00> - "~"
Context Specific [2 0x02] <82> Len:1 <01>
<00> - "~"
Context Specific [11 0x0B] <8B> Len:1 <01>
<00> - "~"
Context Specific/C [1 0x01] <A1> Len:23 <17>
Integer(2 0x02) <02> Len:1 <01>
<41> - "A"
OID(6 0x06) <06> Len:4 <04>
<2B 0C 09 01> - "+~~~"
Context Specific [0 0x00] <80> Len:12 <0C>
<CC F3 F1 E8 ED 20 D0 F3-F1 EB E0 ED> - "~~~~~ ~~~~~~"
ASN.1 end
nfe NetworkFacilityExtension Context Specific/C [10 0x0A]
sourceEntity Context Specific [0 0x00] = 0 0x0000
destinationEntity Context Specific [2 0x02] = 0 0x0000
interpretation Context Specific [11 0x0B] = 0 0x0000
INVOKE Component Context Specific/C [1 0x01]
invokeId Integer(2 0x02) = 65 0x0041
operationValue OID(6 0x06) = 43.12.9.1
operationValue = ROSE_Unknown
Skipping unused constructed component octets!
!! ROSE invoke operation not handled! ROSE_Unknown
q931.c:6888 post_handle_q931_message: Call 32794 enters state 4 (Call Delivered). Hold state: Idle
-- DAHDI/1-1 is ringing
q931.c:4552 q931_alerting: Call 85 enters state 7 (Call Received). Hold state: Idle

> DL-DATA request
> Protocol Discriminator: Q.931 (8) len=9
> TEI=0 Call Ref: len= 2 (reference 85/0x55) (Sent to originator)
> Message Type: ALERTING (1)
TEI=0 Transmitting N(S)=102, window is open V(A)=102 K=7

> Protocol Discriminator: Q.931 (8) len=9
> TEI=0 Call Ref: len= 2 (reference 85/0x55) (Sent to originator)
> Message Type: ALERTING (1)
> [1e 02 81 88]
> Progress Indicator (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) 0: 0 Location: Private network serving the local user (1)
> Ext: 1 Progress Description: Inband information or appropriate pattern now available. (8) ]

< Protocol Discriminator: Q.931 (8) len=44
< TEI=0 Call Ref: len= 2 (reference 26/0x1A) (Sent to originator)
< Message Type: CONNECT (7)
< [1c 25 91 aa 06 80 01 00 82 01 00 8b 01 00 a1 17 02 01 42 06 04 2b 0c 09 02 80 0c cc f3 f1 e8 ed 20 d0 f3 f1 eb e0 ed]
< Facility (len=39, codeset=0) [ 0x91, 0xAA, 0x06, 0x80, 0x01, 0x00, 0x82, 0x01, 0x00, 0x8B, 0x01, 0x00, 0xA1, 0x17, 0x02, 0x01, 'B', 0x06, 0x04, '+', 0x0C, 0x09, 0x02, 0x80, 0x0C, 0xCC, 0xF3, 0xF1, 0xE8, 0xED, ' ', 0xD0, 0xF3, 0xF1, 0xEB, 0xE0, 0xED ]
Received message for call 0x840c020 on 0xb7565fd0 TEI/SAPI 0/0, call->pri is 0xb7565fd0 TEI/SAPI 0/0
-- Processing IE 28 (cs0, Facility)
-- Delayed processing IE 28 (cs0, Facility)
ASN.1 dump
Context Specific/C [10 0x0A] <AA> Len:6 <06>
Context Specific [0 0x00] <80> Len:1 <01>
<00> - "~"
Context Specific [2 0x02] <82> Len:1 <01>
<00> - "~"
Context Specific [11 0x0B] <8B> Len:1 <01>
<00> - "~"
Context Specific/C [1 0x01] <A1> Len:23 <17>
Integer(2 0x02) <02> Len:1 <01>
<42> - "B"
OID(6 0x06) <06> Len:4 <04>
<2B 0C 09 02> - "+~~~"
Context Specific [0 0x00] <80> Len:12 <0C>
<CC F3 F1 E8 ED 20 D0 F3-F1 EB E0 ED> - "~~~~~ ~~~~~~"
ASN.1 end
nfe NetworkFacilityExtension Context Specific/C [10 0x0A]
sourceEntity Context Specific [0 0x00] = 0 0x0000
destinationEntity Context Specific [2 0x02] = 0 0x0000
interpretation Context Specific [11 0x0B] = 0 0x0000
INVOKE Component Context Specific/C [1 0x01]
invokeId Integer(2 0x02) = 66 0x0042
operationValue OID(6 0x06) = 43.12.9.2
operationValue = ROSE_Unknown
Skipping unused constructed component octets!
!! ROSE invoke operation not handled! ROSE_Unknown
q931.c:6919 post_handle_q931_message: Call 32794 enters state 10 (Active). Hold state: Idle

> DL-DATA request
> Protocol Discriminator: Q.931 (8) len=5
> TEI=0 Call Ref: len= 2 (reference 26/0x1A) (Sent from originator)
> Message Type: CONNECT ACKNOWLEDGE (15)
TEI=0 Transmitting N(S)=103, window is open V(A)=103 K=7

> Protocol Discriminator: Q.931 (8) len=5
> TEI=0 Call Ref: len= 2 (reference 26/0x1A) (Sent from originator)
> Message Type: CONNECT ACKNOWLEDGE (15)
-- DAHDI/1-1 answered DAHDI/31-1
q931.c:4683 q931_connect: Call 85 enters state 8 (Connect Request). Hold state: Idle

> DL-DATA request
> Protocol Discriminator: Q.931 (8) len=14
> TEI=0 Call Ref: len= 2 (reference 85/0x55) (Sent to originator)
> Message Type: CONNECT (7)
TEI=0 Transmitting N(S)=104, window is open V(A)=103 K=7

> Protocol Discriminator: Q.931 (8) len=14
> TEI=0 Call Ref: len= 2 (reference 85/0x55) (Sent to originator)
> Message Type: CONNECT (7)
> [18 03 a9 83 9f]
> Channel ID (len= 5) [ Ext: 1 IntID: Implicit Other(PRI) Spare: 0 Exclusive Dchan: 0
> ChanSel: As indicated in following octets
> Ext: 1 Coding: 0 Number Specified Channel Type: 3
> Ext: 1 Channel: 31 Type: CPE]
> [1e 02 81 82]
> Progress Indicator (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) 0: 0 Location: Private network serving the local user (1)
> Ext: 1 Progress Description: Called equipment is non-ISDN. (2) ]
-- Native bridging DAHDI/31-1 and DAHDI/1-1

< Protocol Discriminator: Q.931 (8) len=5
< TEI=0 Call Ref: len= 2 (reference 85/0x55) (Sent from originator)
< Message Type: CONNECT ACKNOWLEDGE (15)
Received message for call 0xb6fd9b90 on 0xb7565fd0 TEI/SAPI 0/0, call->pri is 0xb7565fd0 TEI/SAPI 0/0
q931.c:7024 post_handle_q931_message: Call 85 enters state 10 (Active). Hold state: Idle
asterisk*CLI>


< Protocol Discriminator: Q.931 (8) len=9
< TEI=0 Call Ref: len= 2 (reference 85/0x55) (Sent from originator)
< Message Type: DISCONNECT (69)
< [08 02 81 9f]
< Cause (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) Spare: 0 Location: Private network serving the local user (1)
< Ext: 1 Cause: Normal, unspecified (31), class = Normal Event (1) ]
Received message for call 0xb6fd9b90 on 0xb7565fd0 TEI/SAPI 0/0, call->pri is 0xb7565fd0 TEI/SAPI 0/0
-- Processing IE 8 (cs0, Cause)
-- Found active call: 0xb6fd9b90 cref:85
q931.c:7201 post_handle_q931_message: Call 85 enters state 12 (Disconnect Indication). Hold state: Idle
-- Channel 0/31, span 1 got hangup request, cause 31
-- Executing [h@from_int:1] Hangup("DAHDI/31-1", "") in new stack
q931_hangup: other hangup
NEW_HANGUP DEBUG: Calling q931_hangup, ourstate Active, peerstate Connect Request, hold-state Idle
q931.c:4768 q931_disconnect: Call 32794 enters state 11 (Disconnect Request). Hold state: Idle

> DL-DATA request
> Protocol Discriminator: Q.931 (8) len=9
> TEI=0 Call Ref: len= 2 (reference 26/0x1A) (Sent from originator)
> Message Type: DISCONNECT (69)
TEI=0 Transmitting N(S)=105, window is open V(A)=105 K=7

> Protocol Discriminator: Q.931 (8) len=9
> TEI=0 Call Ref: len= 2 (reference 26/0x1A) (Sent from originator)
> Message Type: DISCONNECT (69)
> [08 02 81 90]
> Cause (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) Spare: 0 Location: Private network serving the local user (1)
> Ext: 1 Cause: Normal Clearing (16), class = Normal Event (1) ]
-- Hungup 'DAHDI/1-1'
== Spawn extension (from_int, 191, 1) exited non-zero on 'DAHDI/31-1'
q931_hangup: other hangup
NEW_HANGUP DEBUG: Calling q931_hangup, ourstate Disconnect Indication, peerstate Disconnect Request, hold-state Idle
q931.c:4721 q931_release: Call 85 enters state 19 (Release Request). Hold state: Idle

> DL-DATA request
> Protocol Discriminator: Q.931 (8) len=9
> TEI=0 Call Ref: len= 2 (reference 85/0x55) (Sent to originator)
> Message Type: RELEASE (77)
TEI=0 Transmitting N(S)=106, window is open V(A)=105 K=7

> Protocol Discriminator: Q.931 (8) len=9
> TEI=0 Call Ref: len= 2 (reference 85/0x55) (Sent to originator)
> Message Type: RELEASE (77)
> [08 02 81 9f]
> Cause (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) Spare: 0 Location: Private network serving the local user (1)
> Ext: 1 Cause: Normal, unspecified (31), class = Normal Event (1) ]
-- Hungup 'DAHDI/31-1'

< Protocol Discriminator: Q.931 (8) len=5
< TEI=0 Call Ref: len= 2 (reference 85/0x55) (Sent from originator)
< Message Type: RELEASE COMPLETE (90)
Received message for call 0xb6fd9b90 on 0xb7565fd0 TEI/SAPI 0/0, call->pri is 0xb7565fd0 TEI/SAPI 0/0
q931.c:7083 post_handle_q931_message: Call 85 enters state 0 (Null). Hold state: Idle
q931_hangup: other hangup
NEW_HANGUP DEBUG: Calling q931_hangup, ourstate Null, peerstate Null, hold-state Idle
NEW_HANGUP DEBUG: Destroying the call, ourstate Null, peerstate Null, hold-state Idle

< Protocol Discriminator: Q.931 (8) len=5
< TEI=0 Call Ref: len= 2 (reference 26/0x1A) (Sent to originator)
< Message Type: RELEASE (77)
Received message for call 0x840c020 on 0xb7565fd0 TEI/SAPI 0/0, call->pri is 0xb7565fd0 TEI/SAPI 0/0
q931.c:7123 post_handle_q931_message: Call 32794 enters state 0 (Null). Hold state: Idle
q931_hangup: other hangup
NEW_HANGUP DEBUG: Calling q931_hangup, ourstate Null, peerstate Release Request, hold-state Idle

> DL-DATA request
> Protocol Discriminator: Q.931 (8) len=9
> TEI=0 Call Ref: len= 2 (reference 26/0x1A) (Sent from originator)
> Message Type: RELEASE COMPLETE (90)
TEI=0 Transmitting N(S)=107, window is open V(A)=107 K=7

> Protocol Discriminator: Q.931 (8) len=9
> TEI=0 Call Ref: len= 2 (reference 26/0x1A) (Sent from originator)
> Message Type: RELEASE COMPLETE (90)
> [08 02 81 90]
> Cause (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) Spare: 0 Location: Private network serving the local user (1)
> Ext: 1 Cause: Normal Clearing (16), class = Normal Event (1) ]
q931_hangup: other hangup
NEW_HANGUP DEBUG: Calling q931_hangup, ourstate Null, peerstate Null, hold-state Idle
NEW_HANGUP DEBUG: Destroying the call, ourstate Null, peerstate Null, hold-state Idle
asterisk*CLI>

попробовал увеличить время разговора большим числом в секундах, все равно рвет на 599-й или 600-й

< Message Type: DISCONNECT (69)
Вот и ответ. Астериск непричем.

< Ext: 1 Cause: Normal, unspecified (31), class = Normal Event (1) ]
И кауз код 31, а не 16...

Смотрите логи с той стороны и ищите там причину.

Да, спасибо большое. Сам вчера разобрался, но вам и Alekz спасибо, что отреагировали и натолкнули на мысль. :)

Я просто у нашего специалиста по АТС спрашивал об ограничении времени разговора, потом сам посмотрел. Действительно ограничение отключено, НО! Проблема как раз шла со стороны Панасоника. Попробовал для транковой группы, идущей на *, включить органичение времени разговора и поставить интервал 20 минут. И ВУАЛЯ!!!! Все заработало. Получается, что панасоник ограничивал время разговоров временем по умолчанию даже в отключенном режиме ограничения времени. :)